Used Forklifts Downey - Narrow aisle forklifts are usually utilized in warehousing applications. These forklifts are vital equipments within the business because their extreme maneuverability and small size enable warehouses to use space to maximum storing capacity. They could easily negotiate aisles that are 1.8 meters wide, whereas typical lift trucks need at least 3.4 meters of aisle width. This kind of forklift is sub-categorized as "narrow aisle forklifts" and "very narrow aisle forklifts". The first require 2.4 meters - 3 meters in aisle width, while the latter can function in a 1.8 meters wide space. The design of a narrow aisle forklift includes forks positioned at right angles to the body of the truck. The trucks do not need to face the shelves, but instead drive straight down the aisle picking up loads to the side. This particular design feature is the key to their suitability for limited spaces. To be able to make sure that the forklift is moving in a straight line down the aisle, some very narrow aisle forklifts consist of optical or wire systems. That way, the operator can focus more on the picking and the placement of loads. The cushion tires that come with these types of lifts are made of solid rubber. The hard tires perform well on paved, smooth surfaces and concrete floors. Narrow aisle forklifts have electric motors suited for use in indoor environments. Propane-powered models are available too. Telescopic handlers are a bit like forklifts. It has a single telescopic boom that extends forwards and upwards from the truck, and a counterweight located in the rear. It functions much more like a crane than a forklift. The boom can be equipped with a variety of attachments. The most common attachment is pallet forks, but the operator can also attach a muck grab, lift table or bucket. Also called a telehandler, this type of equipment is commonly utilized in agriculture and industry. When it is hard for a standard forklift to access places, a telehandler is frequently utilized to transport loads. Telehandlers are frequently used to unload pallets from inside a trailer. They are also more handy than a crane for lifting loads onto other high places and rooftops. The telehandler has one major limitation. Even with rear counterweights, the weight-bearing boom can cause the machine to destabilize while it extends. Thus, the lifting capacity lessens when the distance between the center of the load and the front of the wheels increases. The Matbro company developed telehandlers in England. Their design was based on articulated cross country forklifts utilized in forestry. Initial models had a driver's cab on the back section and a centrally mounted boom on the front, but these days the most popular design has a rigid chassis along with a side cab and rear mounted boom. Hyster is well-known as a world leader in forklift trucks. However, it started as a producer of lifting machines as well as winches. Most of its production was focused in the northwest United States and dealt primarily with the wood and logging industry. A couple years after the 1st forklift trucks were invented Hyster became synonymous with quality manufacturing. Over the previous 80 years Hyster has continued to get bigger and develop its product line. The growth of its products coupled with its wish to stay service oriented has allowed Hyster to grow into the global player it is today. Since 1992, Toyota Material Handling inc., U.S.A., also referred to as TMHU, have been the top selling lift truck provider in the U.S. This company has been based out of Irvine, California for well over 40 years, providing a wide-ranging line of quality lift trucks. With a first-rate reputation of resilience and reliability, Toyota lift trucks have thrived in the competitive resources handling market. Quality is the keystone of Toyota’s legendary Toyota Production System practiced at all manufacturing facilities, including TIEM, which is stands for Toyota Industrial Equipment Manufacturing, located in Columbus, Indiana. The bulk of the Toyota lift trucks sold in the U.S. are built here. Every one of Toyota's manufacturing facilities within Canada and the U.S. comply with the International Organization for Standardization or ISO 14001 standard. TIEM has been honored many times for its dedication to continuous improvement, and its environmental methods. It is the first and only manufacturer to offer EPA and CARB-certified Compressed Natural Gas powered lift trucks on the market. To illustrate, the Toyota 8-Series IC lift trucks emit 70% fewer smog forming emissions than the existing federal EPA standards and have complied with California’s strict emission standards and regulations. In the world of crawler excavators, heavy equipment accessories, dump trucks, log loaders and wheel loaders, Doosan Heavy Construction equipment produces them all. Worldwide, Doosan has raised its share of the current market to develop into the 5th most significant manufacturer of construction equipment. Started as a trading business in 1986 within South Korea, known as Park Seung Jik Store located in what was once Baeogai and is now Jongno 4-ga, Seoul. The organisation focused on becoming an national infrastructure services business in 1996 and is also the longest running and oldest organization in South Korea this very day. Immediately after acquisitions in 2005, such as Daewoo Heavy Industries & Machinery, now termed Doosan Infracore, Doosan has grown to be a international conglomerate, concentrating on the construction market place. The business developed into the world’s foremost small construction equipment supplier by 2007, after purchasing Bobcat USA, worth 4.9 billion. Doosan Group has expanded to become the 7th most well known construction machinery dealer anywhere, operating in thirty-seven nations around the world with close to 38K employees. Doosan celebrated the roll-out of its four hundred thousandth excavator in 2018.
Taylor: Used Taylor Warehouse Forklifts Downey - Narrow Aisle Lift trucks There are particularly designed forklifts which operate in narrow warehouse aisles. These machinery are often known as vary narrow aisle or narrow aisle lift trucks. They could easily negotiate smaller aisles and enable you to enjoy several benefits. For instance, the increased amount of space to keep stuff can greatly increase the overall available stock of a company. The narrow aisle lift truck is manufactured to maneuver rather easily, because they are engineered specially to operate in tight areas. Their different design has eliminated many of the items which are squished up into the main body of the conventional lift truck design. The downside of narrow aisle forklifts is that they are very slow compared to standard lift trucks. Narrow aisle lift trucks would not work if you need to transport items across long distances. When it comes to speed they will not be a dependable option. If you also have a regular lift truck, this would not be an issue. You could just utilize the narrow aisle forklift to transport the load to a central place and after that hand it off to a regular forklift which could travel the bulk of the distance in a timely and efficient way. Frequently, narrow aisle forklifts cannot handle as much lifting weight; therefore, outside of smaller loads they will not be really helpful. Electric Forklifts Traditional gas lift trucks are not a suitable choice for indoor use like warehouses or stores. They would not be as safe because of their fumes, or as cost-efficient or useful than an electric powered unit. Electric forklifts are normally designed to work and look a lot like gas ones, but they utilize electric batteries which must be recharged, rather than gasoline fuel. The electrically powered forklift has become more popular and for a range of reasons. These machines can help companies save costs on fuel. Electric models will initially cost more, but will ultimately save you more over time. For example, when gas prices go up, you would not be affected and would save a lot of cash. Electric models tend to last quite a bit longer as opposed to gas powered units also. This is partly due to the fact they are mostly utilized inside and thus don't get as dirty or work in as harsh settings as the gas powered ones. Electric units are healthier to utilize in areas which are badly ventilated like warehouses and indoor operations as they don't emit noxious fumes. It can be extremely dangerous to use gas or diesel forklifts inside. The electric forklift does have several downsides like the fact that they can really only work for roughly 8 hours. Then the machinery would have to be charged for 8 hours and rested for another 8 hours. Numerous businesses get around this situation by buying a spare battery so they could have less downtime and continually cycle them. There are fast charge batteries emerging on the market which are also minimizing the charging time.
Nissan: Used Nissan Lifts Downey - Compact forklifts made by Nissan are ideally suited where both outdoor and indoor forklifts are required. They provide workers with an exceptionally versatile alternative. These compact models provide excellent maneuverability and tight handling, making them ideal for warehouse use indoors. Their compact chassis is responsible for their extreme versatility. Solid pneumatic tires offer remarkable performance out in the yard and on improved surfaces. The lift trucks are all produced using Nissan industrial engines. Greater torque and better horsepower satisfy a range of manufacturing, recycling and warehouse operations along with other indoor/outdoor conditions. The Nissan lift trucks are offered in liquid propane or LP, or Dual Fuel with LP/gas. The fuel management system optimizes engine operation so as to provide excellent fuel efficiency and reduced HC, CO and NOx exhaust emissions. Each and every compact unit is offered with the standard comprehensive engine protection system. This particular system is in place so as to warn operators in the event of of a severe drop in oil pressure or any excessive heat. This particular system offers extended drive train life and engine life for your forklift investment. Operator Comfort and Control There is plenty of head, leg and foot room built into every operator compartment and is versatile enough to handle different sized drivers. The forklift offers a standard full suspension seat that has hip restraint and soft touch arm pads to offer utmost operator comfort and enhanced safety. The low profile design of the unit offers plenty of head clearance. There is also a front to back travel adjustment to enable a customized fit so as to accommodate practically any operator height. Nissan's K-series engines offer the same proven block design and bottom by-pass cooling system like the H-Series engine, its' predecessor. These improved and new engines are specially tested and designed for industrial use in order to provide all of the power and torque, in the low rpm range, to suit the needs of the application. The K21engine has a transmission/engine warning system and protection that is an additional safety measure that is added for your investment. It helps by decreasing the speed in case of low oil pressure or excessive heat generation.
Raymond: Used Raymond Stand Up Forklift Downey - Raymond provides counterbalanced trucks so as to provide their operators with maximum confidence and reliability, from dock to stock. These equipment offer strong AC drive, enhanced comfort and excellent lift capacity. This innovative technology helps to increase production with more torque, smoother and faster operation, less downtime and better acceleration. Raymond is proud to provide many stand-up counterbalanced trucks which will deal with all of your particular material handling needs effectively and efficiently. Raymond Counterbalanced Truck Model 4150 Highly Productive Without sacrificing any output, the company is capable of improving speed and efficiency. These specific machines are both easy to operate and maneuver. The larger jobs get done utilizing the counterbalanced truck and its 3000 and 3500 pound load capacity. The Model 4150 forklift is a powerhouse within its class, with speed and power options combined with its rough dock applications. This model is perfect for productivity requirements and warehouse systems. Additional torque and stamina is featured with the strong AC drive which gives the Model 4150 lots of desirable features to add to the ease of operation for numerous rough dock applications. Raymond Counterbalanced Truck Model 4250 When choosing a Raymond Counterbalanced Truck Model 4250, you are choosing to go with a versatile powerhouse. The new ComfortStance suspension has incorporated the counterweight of the vehicle into the floor. This design has ensured the unit requires no adjustment. The operator's comfort is really improved with the ComfortStance suspension. The Single-Axis Control Handle enables the operator to secure a solid grip point and a stable, comfortable ride that is especially made in order to fit the hand. There is a 3-tiered scalloped armrest so that it is able fit operators of different sizes. A clear view of your work area can be attained with Raymond's newly designed clear view mast. This gives operators a clearer line of site to the load, which ends up providing more efficient handling and stacking overall and less product damage. The new angled design covers offer the opportunity for visibility so as to see loads right to the floor. The load capacities range from 3000 to 5000 pounds making them really strong equipment.
Kalmar: Used Kalmar Counterweight Forklifts Downey - Tips for Purchasing Forklift Parts When you are considering buying parts for your lift truck, there are some things you will benefit from knowing about. Several of the things, they may not tell you otherwise, therefore it is a good idea to know about what those tips are so that you can save yourself lots of time and money in the long-run. You must know the size of machinery you will need, when you go looking for a machine. This will allow you to concentrate on your requirements and would save you wasted time spent on machinery that offer you less value. It is truly easy to guesstimate and accidentally jump the gun when you need a particular component, thus, you must know what forklift model you have and what items it requires. There is a wide array of places that sell parts for lift trucks, so make sure to do some research to know all the best alternatives for you. Taking the time to compare prices ahead of time would prepare you for how much you should spend and get you ready to make the investment. Because replacement parts are usually rather pricey, compare some prices to see if what store offers the best cost. Forklifts are high maintenance equipment since they work hard each time they are being utilized. In order for the model to safely and efficiently run, it is vital to invest in replacing worn out and broken components as soon as they are discovered. Some individuals even shop on-line and look for the availability and best pricing that way. There may be a variety of areas within your area carrying these components and pricing out ahead of time would save you from driving all over town. Find someone who specializes in your specific brand of machinery, if you are not sure as to the parts you need. They would likely be able to educate you about what parts you need. Ask around with individuals with the same lines of business about where and whom they go to have maintenance done and shop for parts. If you have no one to speak with directly, you could always read where others go and look on blogs.
Genie: Used Genie Scissor Lifts Downey - All Genie material lifts have been designed to be powerful and reliable machinery able to operate indoors and outdoors and able to deal with a huge variety of applications. In each of Genie's lightweight and portable units, reliable, high quality and performance could be expected. Genie is a cost-effective solution for many work site applications. Genie material lifts are easily set up by just one person and can be ready to work in no time. All lifts can be set up, transported, and utilized in a standard-sized service truck or pickup truck. The Genie telescopic pneumatic hoists are portable, light weight, and are a compact size, making them ideal for lifting all kinds of cargo into position for installation jobs. A lot of options and accessories are available to make each and every machinery meet individual work requirements. The first Genie Hoist was launched into the workplace during 1966. This equipment became so popular due to its usefulness, portability and uniqueness that Genie continued to develop its product into the diverse range of machinery available on the market these days. The Genie Super Hoist is a highly portable telescopic pneumatic hoist which utilizes CO2 or compressed air. This equipment can lift loads up to 136 kilograms to heights of 3.8 meters or 113 kilograms to heights of 5.6 meters. The user could complete around 80 to 90 lifts on one tank of compressed air or CO2. A 9 kilogram tank is offered as an accessory choice but the bottle mounting bracket can fit any common size CO2 bottle. When not in use, the 4.87 meter long hose could be stored around brackets that are beneath the platform. Genie hoists have a patented pistol-grip control handle where the dump valve and up and down functions are activated. This control handle could clip onto a storage button on the cylinder's side when not being used. Genie has been developing and providing products for various kinds of work sites ever since their introduction in the year 1966. These machines provide a helpful addition to your work site equipment for both outdoor and indoor jobs.
Comedil: Used Comedil Construction Cranes Downey - Crawler Crane The mobile crawler crane is specific crane made with either a lattice boom or a telescopic boom. These move upon the crawlers tracks. As this crane is self-propelled, it could move around particular work locations without the need for a lot of set up. Because of their huge weight and size, crawler cranes are are difficult to transport from one site to another and are fairly costly. The crawler's tracks offer stability to the equipment and enable the crane to work without using outriggers, although, there are some units which do utilize outriggers. Also, the tracks provide the machine's movement. Early Mobile Cranes The very first mobile cranes were originally mounted to train cars. They moved along short rail lines that were specially constructed for the project. When the 20th century arrived, the crawler tractor evolved and this brought the introduction of crawler tracks to the construction business as well as the agricultural industry. Not long after, the crawler tracks were adopted by excavators and this further showcased the equipment's versatility. It was not long after before crane manufacturers decided that the crawler track market was a safe bet. The First Crawler Crane Northwest Engineering, a crane company within the USA, was the very first to mount its crane on crawler tracks in the 1920s. It described the new machine as a "locomotive crane, independent of tracks and moveable under its own power." By the mid-1920s, crawler tracks had become the chosen means of traction for heavy crane uses. The Speedcrane Developed by Charles and Ray Moore of Chicago, Illinois; the Moore Speedcrane was among the first to attempt to copy rail lines for cranes. Manufactured within Fort Wayne, Indiana, the Speedcrane was 15 ton, steam-powered, wheel-mounted crane. In the year 1925, a company called Manitowoc Shipbuilding Co, from Manitowoc, Wisconsin recognized the potential and the marketability of the tracked crane. They decided to team up with the Moore brothers so as to manufacture it and go into business.
Caterpillar: Used Caterpillar High Capacity Forklifts Downey - Forklift Motors Purchasing a forklift is something you must think about carefully. A forklift is a large capital expenditure, and a complex machine with a motor strong enough to perform heavy-lifting tasks. The price tag for a forklift ranges from $10,000 to $30,000, comparable to the cost of a small truck. If buying a second-hand forklift, be certain to have it inspected for potential mechanical problems. There are two various kinds of forklift motor: internal combustion or electric. Forklifts with electric motors are usually more costly than forklifts with internal combustion motors. The size of the motor must suit the type of work for which the forklift will be used. A forklift with a large motor costs more compared to a forklift with a smaller motor. Gasoline or propane powered motors are commonly stronger than electric motor and are capable of lifting heavier weight. The disadvantage is that gas motors tend to develop issues more frequently compared to electric motors. Depending on the price of gas or propane, gas powered forklifts could be more costly to run compared to electric powered forklifts. Reliable forklift manufacturers comprise Mitsubishi Caterpillar, Crown Equipment Corp., Toyota Industries and NACCO Industries. Before deciding, research the different manufacturers and the availability of parts. Prices, reviews and testimonials could be found on-line.
Gradall: Used Gradall Telescopic Handlers Downey - The telehandlers designed and made by Gradall have established a reputation in the industry for their dependability, low cost of ownership and strength. Furthermore, they are extremely popular for their exclusive 90-degree rear-pivot steering. This feature is actually what sets Gradall Telescopic Handlers apart from the others. These machines are capable of turning sharp corners and offer excellent maneuverability in even the tightest of work places, allowing operators to take these machinery where other telehandlers are not capable of working. These Gradall machines are capable of moving down narrow aisles as well as back in crowded landing locations with better speed and accuracy. These units could also square-up lumber. The ergonomically designed and spacious machinery cab offer a clear view of the job site. Gradall's telehandlers are equipped with different kinds of attachments to be able to complete a wide range of tasks. There is practically nothing a Gradall Telehandler cannot do, in order to accomplish the high performance level you require to get the task finished. JLG Telehandlers JLG Telehandlers are known for their originality, strength and extreme versatility. These are the main components that the JLG family of all-wheel-steer telehandlers. Their 1 compact unit, together with their 5 full-sized units enable you as well as your company to tackle any jobsite challenge with ease and efficiency. These machines have the capabilities of better overall visibility, a centered cab design and a high-boom pivot. Each JLG telehandler could be equipped with numerous attachments. More versatility, power and capacity are provided by JLG telehandlers. These machines make a great addition to any fleet. Numerous smaller companies choose to rent different brands and units before deciding to buy anything very pricey. This is an excellent alternative to experiment with the telescopic handlers available on the market and find the exact model to suit your requirements. The minute you climb into the telehandler cab, your productivity is on the line. The JLG lineup of all-wheel steer telehandlers gives you the dependability, power and maneuverability that has become the expected standard of this world-leading machine manufacturer. With load capacities from 5500 to 12,000 lbs. and heights of up to 55 feet any jobsite challenge can be attained with these specific choice and place telehandler units.
Snorkel: Used Snorkel Boom Lifts Downey - Wally Johnson, back in the year 1946, created the markets for both scaffold towers and aerial work platforms all by himself. He did this by establishing a company that was referred to as UpRight. Mr. Wally Johnson was an extremely skilled mechanical engineer who resided in Berkeley, California. He stumbled upon access machinery when he began searching for a solution to painting his home. Mr. Johnson found it hard to search for capable scaffolding when he started a house painting project. Existing scaffolding could not deal with the uneven ground on his land. After being extremely discontented with his options, he decided to design his own aluminum scaffold tower together with adjustable legs. In that same year, the Snorkel Company was founded in St. Joseph, Missouri. The company was responsible for introducing an innovative new elevating boom lift to the market. The equipment was produced for firefighting and rescue work. In less than twenty years, the technology had developed into self-propelled boom lifts. The first self-propelled lift was sold by Snorkel in the year 1977. This specialized product line did not take long to become the company's main business. It did not take long for Wallace Johnson to catapult to the top of the industry and attain global domination with his scaffold. After he had attained this field, he decided to start all over and make the world's very first self-propelled aerial lift. Mr. Johnson in 1972, opened a factory within Selma, where he manufactured the "Flying Carpet" scissor lift. After this exciting and new equipment exploded onto the marketplace, the ground-breaking product soon out-ranked the scaffolding component as the main source of revenue of the company. Wallace Johnson passed away in the year 1980. At that time, the company UpRight Inc. was sold but his inventive and pioneering spirit lived on. In the year 1994, UpRight introduced the world's first micro-scissors. They went on to pioneer the TM12, that is the self-propelled mast lift.
Skytrak: Used Skytrak Zoom Boom Downey - There are 5 models varying in range capacity, reach capacity and lift height. Everyday you will be turning corners on job performance and attaining new goals. These machinery will keep performing job after job, even in the most difficult environments and roughest terrain. With 3 steering modes, you will have all you require to deal with all the maneuverability to handle challenging and varied terrain. When you have to take productivity levels to the next level the Model 10054 provides 4-wheel steer and 4-wheel drive to be able to successfully accomplish the tasks that require the most mobility. Stabil-Trak System WIth the patented Stabil-Trak system in place, operator confidence is increased. The Stabil-Trak technology will provide rear axle stabilization that enables the automatic transfer from a 3-point stance to a 4-point stance in order to increase stability. The system operates in free-pivot and final positioning locked modes. With both the effectiveness and power of Stabil-Trak technology working with you, you will notice much more operator confidence and a superior level of boosted performance on the jobsite. The Stabil-Trak system in addition to the axle mounted outriggers operate to allow the frame to become both level and secure without changing the stance. The Right Dimensions SkyTrak Zoom Booms will offer an overall height of as much as 101 inches on certain models, in addition to a ground clearance of as much as eighteen inches. This would enable the operator to have better access to areas of low-clearance and more room to travel over debris. The navigation of confined areas is a lot less difficult with the tight turning radii. These are several of the features that allow you to maneuver your way through the most productive day you could. Firestone Tires Last Longer SkyTrak telehandlers are exclusively equipped with Firestone DuraForce MH tires. New Firestone tires will lower your ownership cost because they can last 3 times longer than other tires and are far less prone to damage to the tires sidewall. Since these tires are available in various unique sizes, there are fewer parts to stock. This leads to an overall reduction of inventory expenses. To be able to optimize performance in rough terrain, lesser ground bearing pressure is offered by a self-cleaning tread pattern. On each SkyTrak equipment, there is great attention to detail put on the overall design and engineering. From the frame, down to the tires, to the cab interior, a strict attention to detail has allowed these machines to be developed in the most economical way for the equipment to be made and offers the operators with the most dependable alternative for the jobsite.
Fantuzzi: Used Fantuzzi Reach Stacker Downey - The Reach Stacker range by Fantuzzi is manufactured by Terex. These machinery are cost effective and well designed and engineered to be strong and durable. The Fantuzzi Reach Stacker is very cost effective to run. These types of machinery have earned a status of being able to work within the most intense environments with a dedicated reliability which has come to be associated with the Fantuzzi name. All items by Fantuzzi are supported by excellent technical support, service and an efficient parts department located in the United Kingdom. For working in medium to small port environments, the Fantuzzi Reach Stacker provides a flexible handling solution. It offers you the ability transport containers over short distances in an effective and fast manner, while being able to easdily stack them. Over the last several years, reach stackers have become exceedingly popular in the container handling industry. Compared to a standard lift truck, these equipment are a lot more flexible. The Reach Stacker has a larger storage capacity and an overall higher stacking capacity. These particular features can prove very helpful on the jobsite or inside the warehouse. Much More About Reach Stackers Fantuzzi engineers and designs very high quality products capable of rotating containers and after that stacking them end on. When certain selectivity is required for block stacking, Reach Stackers are an ideal solution and are well suited to operate in combination scenarios. These models are usually found in rail and ports terminals. Laden Container Reach Stackers Throughout the range, first row capacities of 45 tons are provided. Second and third row capacities alter depending on you needs and the particular model. The Fantuzzi Reach Stacker is cost effective to operate. As well, it's durable design makes it a strong machinery that can demonstrate maneuvers that are very effective.
Yale: Used Yale Narrow Aisle Forklifts Downey - Yale is a top manufacturer of zero emissions electric lift trucks within the North American Market. The company was amongst the first to start utilizing the energy efficient AC motor and other control technology. Yale's continued pursuit of superior energy efficiency is improved further by competitive testing. These testing results feature that Yale's 5000 pound electric rider unit offers the best energy used per load transported, or energy efficiency, of any type of forklift within its category within North America. Green Innovations Yale was able to develop and introduce a ground-breaking electronically controlled transmission that can really reduce the brake and tire wear for our ICE lift truck clients. With regards to our electric trucks, the company has implemented a particular system to recapture energy into the lift truck during braking and during the lowering of loads. This energy could then be utilized again. This process really lowers the unit's overall energy consumption. Yale has been able to apply many innovative engineering techniques that have helped to minimize the vehicles non-productive energy. These techniques have helped to enhance its hydraulic system efficiency, drive train efficiency and weight reduction. There are still patents pending on the drive train efficiency. Green Initiatives Over the past several decades, Yale has gone the extra mile in engineering their lift trucks to be compatible with all the latest in alternative power technologies. The business has applied clean diesel fuels, LPG option and electric battery models. This tradition is being upheld most recently, with the business being among the first to implement working fuel cells in actual applications. Through engineering teamwork, Yale has supported the application of many greener technologies. In addition, we have started a new system of field validation testing, and analysis. Presently, we are investigating in more efficient battery chemistries and technologies, to be able to reduce overall energy use, decrease toxic material content and increase productivity. Yale is strongly devoted to these green initiatives and they are reinforced by the company's participation in setting and developing new industry standards to adopt these greener technologies in a reliable and safe manner. One more prime factor in Yale lift truck design is recyclability. Beginning at the design stage, the company actively chooses materials for its forklifts keeping the recyclability factor in mind. Re-using materials as much as possible and having broken down things to be able to be sent for recycling keeps environmental sustainability at the forefront of our business and greatly decreases our footprint.
Terex: Used Terex Telehandlers Downey - Genie's compact telehandler models are ideal for both large and small scale jobs. These machines are easy to service, simple to maneuver, and come with a lot of different attachment options. Genie compact telehandlers can deal with the requirements of nearly all landscaping, farming, construction and masonry applications. These machines are easy and quick to transport and have been popular for their low stowed height and compact footprint. There are 3 various available steering modes: crab steer, front-wheel and coordinated. There are many interchangeable common parts available for effective maintenance. These machines have been made and designed with no-tool access to daily inspection points in order to keep the maintenance easy. The basic auxiliary hydraulic system is also easily tailored so as to accommodate various types of attachments. Genie has been committed to lifting their clients higher and this philosophy extends past the physical reaching abilities of their products. The company has built a hugely satisfying customer base since they focus on meeting their requirements at every chance. Genie has been proudly making products to solve challenges in the job location since 1966. This process of research and development is a continuous part of their success and Terex strives to become more economical and efficient with every new model. In order to improve their design process for new products, Genie has established a devoted group of engineers and product managers who depend on input from regular customer feedback. This is how they are able to consistently feature the latest technology in order to adapt to their client's ever-changing needs. These new ideas are transformed and manufactured to meet strict standards that help provide amazing value for the future, lessen your costs and increase quality. Genie Telehandlers are available in 3 exciting power-packed models. They are ideal machinery for high reach applications and are also great when you have to secure productivity in a limited-access area. Each unit is available with a large variety of attachments in order to make certain that you have the necessary tools to finish each job. Genie Telehandlers are made to last and to efficiently help you get the task done on time and safely.
Haulotte: Used Haulotte Boom Lifts Downey - Company Profile The Haulotte Group specializes in material handling lifting equipment. They are known for distributing and manufacturing a variety of different heavy industrial machines. Their extensive services and sales are through a subsidiaries network. They offer a wide array of over 60 various types to be able to meet all of their client's requirements. Several of their popular pieces of machinery consist of: Earth moving equipment, Event seating and staging, Utility and system scaffolds, Tele-handlers and Access equipment. In the field of material handling and transport, the Haulotte Group brings over 100 years of expertise. Ever since the 3rd of December, the year 1998, the Haulotte Group has been quoted on the Paris Stock Exchange. Global Player, Haulotte Group's Business Model Covers: The company's business model aims to be successful and flexible in their manufacturing operations. They pride themselves on being diverse and can adapt to the changes and demand in specific market conditions. Haulotte Group offers a distribution network which is based in 20 subsidiaries. They have numerous offices located in strategic markets in more than 100 countries offering coverage, which are supported by a distributor network. To be able to produce additional activity, helping to bring their brands into particular geographical markets, the company has an additional rental business. This helps Haulotte Group be better positioned in order to help assess the requirements of end-users. The rental business offers a great way for customers to become familiar with the products before buying them. Industries: There are 7 various product ranges offered by the Haulotte Group, which helps them meet the requirements of their customers in many different various, like: manufacturing, airports, logistics, maintenance and the retail sector amongst others. The Haulotte Groups strives to give its customers the flexible and successful manufacturing operations that are able to meet the different demand fluctuations in certain market conditions. At present, Haulotte Group offers six production units which could offer the top product solutions to their partners.
Skyjack: Used Skyjack Knuckle Boom Lifts Downey - Boom Truck Like cranes, boom trucks can be equipped with a winch for lifting. It depends on the vehicle size and weight determines the type of load that can be raised. Due to the capability of their size, cranes can normally lift much larger loads. The benefit of boom trucks is that they are mobile and could be driven to work locations which make them a lot more versatile. In addition, a boom truck can be outfitted with a bucket and could also raise materials as well as personnel up to high places. Like for example, boom trucks are commonly found raising maintenance and utility staff on a telephone pole. Types There are various kinds of boom trucks. There are times when the term "boom truck" is synonymously used with vehicles which carry out the same functions. For example, aerial work platforms which are mounted to the bed of a truck which utilizes hydraulic lifts could be referred to as a boom truck. Other people might refer to a regular utility truck utilized to raise employees to a utility a boom truck. Whether the truck utilizes a bucket or a winch, operates on treads or wheels, they could still lift employees and materials vertically. Boom Truck Crane The boom truck crane is used like a crane but is classed as a boom truck. Usually, these types of vehicles are found in hard to reach places and areas that are difficult to reach, which need a heavy lifting vehicle. A boom truck crane can lift different weights. These kinds of equipment remain stationary when lifting. Crane Large cranes are utilized to move construction materials. Cranes are big lifting devices utilized for moving goods or materials. They are common features in the manufacturing industries, the transportation industries and in the construction industry. Cranes utilize chains, cables, ropes or wires connected to a winder. The load capacity depends on the kind of crane. The highest load capacity is provided by big fixed chains.
Toyota: Used Toyota LP Forklifts Downey - Propane cylinders are designed to take up really little space and can be kept inside the storage area or in an outdoor facility. It does take some time to switch out a propane cylinder, although, it still does requires operator training in order to be performed safely and also need knowledge of safety standards such as the Occupational Health and Safety Administration or OSHA. Compared to the electric truck, IC forklifts are faster and easier to refuel. However, the internal combustion engine does produce polluting emissions and are very noisy. NARROW-AISLE FORKLIFTS The ITA's Class 2 trucks consist of a huge variety of electric lift trucks and these are specially made to be used in narrow aisles. The regular storage aisles are 12 feet wide, and this easily allows a counterbalanced lift truck to turn in the aisle and put a load away. Normally, narrow aisles are 8 feet wide, while the very narrow aisles are roughly 5.5 to 6 feet wide. These narrow aisles need specialized lift trucks that are capable of putting away cargo that are small enough to turn on a tight radius or without any turning at all. Turret trucks, order pickers and reach trucks are 3 of the most common narrow-aisle forklifts. The differences amongst these trucks are discussed below. Narrow-Aisle Reach Lift Trucks The traditional reach truck is the original narrow-aisle lift truck and these machinery do not require a counterweight. They are also small enough to turn around in narrow aisles. Instead, stability is provided by the outrigger arms which extend in front of the forklifts. Nonetheless, depending on the storage configuration, these outrigger arms can prevent the lift trucks from getting close enough to the storage rack to retrieve and deposit cargo. To be able to overcome this situation, a pantograph was designed. The pantograph is actually a reach truck that is made with a telescoping mechanism. This enables forks to reach into storage areas concisely and easily. The best environment for narrow aisle forklifts is a place that has good lighting, clean floors and well maintained floor, good traffic flow, along with ample turning space. These types of equipment have changed the material handling business. Toyota stands behind their dedication to giving excellent quality and really strong equipment. As the business changes, they always strive to implement solutions in order to offer their diverse client base with the best products available.
Trek: Used Trek Sweepers Downey - TREK Cleaning Machines is a manufacturer of cleaning machines which have a passion for the cleaning business. The company's innovative nature is a reflection of the company founder's huge entrepreneurial style. Chris Knowlton, Jim Hartsock and Bob O'Hara together have 60 years combined experience in successfully developing, manufacturing, marketing and supporting really efficient equipment which provide supreme value to their clients. TREK is devoted to new design concepts and deeply dedicated to excellence. All these corporate values are reflected in their product development and individual equipment. TREK Cleaning Machines provides a range of products which provide reasonable production gains to their clients in addition to energize their dealer partners. Energy, dedication and commitment to client satisfaction resonate with every equipment. The TREK team enjoys tackling challenging tasks and embracing challenges. They are proud to introduce the Torsion scrubber line, which offers a breakthrough in technology. The Torsion vision project evolved and was motivated from the company's unique understanding of operator's requirements and skills, particular cleaning applications, and the strong desire by owner's to really lessen their expenses through production gains. TREK, along with their dealer-partners are dedicated to having both parts support and technical support whenever you need it. This dedication to offering great service is at the core of their customer service culture. Ensuring that your cleaning equipment is up and running on a daily basis is vital to to TREK and the customers too. TREK provides leading technologies to help deliver reliable machines to lessen your cleaning costs. TREK has become a preferred choice for lots of different businesses. On the market these days, there are many businesses that spend much effort in developing user-friendly cleaning equipment at a great price. In an effort to develop such machinery, TREK Cleaning Machines have been a recognized manufacturer of excellent sweepers and scrubbers for many years. Recently, the company introduced a complete line of industrial floor sweepers and floor scrubbers with a focus on extremely competitive pricing and on increased production. TREK was first established by industry veterans. They know the concerns and issues which face manufacturing facilities. The Stand- Up Rider Scrubber or Torsion SUR was designed together with the Radial Sweeper. The articulated TREK Torsion SUR scrubber machinery has been uniquely engineered with 2 sections that use a pivoting joint to connect them. This specialized design enables the Torsion SUR TB6 scrubber to provide a turning freedom of 150 degrees, better handling, and increased maneuverability. These features in addition to the 60-gallon tanks, that come standard equipped, means an increased productivity of up to 100 percent.
Comansa: Used Comansa Cranes Downey - Linden Comansa was a company which started manufacturing tool and jig during the early parts of the 1960s. They went by the name "Imausa". The company began supplying mainly the larger sub-contractors to the then booming automotive business Around that same time, there was a strong industrial expansion within Spain. This period saw Imausa making more sophisticated machine tools, jigs and various kinds of tools for both in-house and external use. Additionally, the company specialized in making pre-fabricated steel structures particularly for industrial buildings. The company's next and most logical step was into the crane market. The Spanish tourist industry exploded to soon become amongst the biggest tourism magnets within the world. This mass expansion of course brought a parallel demand for schools, housing and hospitals amongst different other things. The company became really busy, really fast. Production The very first cranes that were made were saddle-jib, simple cranes. They were mainly suited to the building methods at that particular time. The first crane model eventually grew into a variety of cranes with a capacity ranging from 12 to 42 metric-tons. Linden Comansa saddle-jib cranes had already met the 200 metric-ton barrier by the early 1970s. Linden Comansa has surpassed the standard and has continued to design and engineer cranes that exceed the 900 metric ton capacity. There is presently manufacturing and design facilities which allow the production and development of even larger and more spectacular machinery. The unique Linden 8000 Modular System crane provides some specific benefits which has made it a popular equipment for Linden Comansa clients all over the globe. These global clients have bought roughly 12,000 Linden Comansa cranes in addition to the roughly 6000 equipments made by Linden-Alimak within Sweden. These other cranes were made before the acquisition of the world-wide manufacturing and selling rights of this specific modular system.
Hyster: Used Hyster End Control Forklifts Downey - At Hyster, we have a diverse variety of forklifts to meet all of your application requirements. For example, the J45-70XN has the Drop Battery Box and unique component design that allows this particular model to use pneumatic tires. Utilizing the pneumatic tires enables for a smoother ride due to reduced vibrations even if the surfaces are rough. This specific electric truck has 4,500 to 7,000 pound capacities for both outdoor and indoor work. These models' electric motor allows them to be a great zero emissions alternatives to various other engines. Hyster offers a series of three wheel trucks as well as four wheel forklifts to suit work areas which require a tight turning radius. The J30-40XNT model is a three wheel forklift which surpasses nearly all other forklifts in its ability to manoeuvre through tight spaces and turn sharp corners. This series of lift trucks is suitable in limited or crowded work spaces, making both loading and unloading easier and safer. This lift truck also features dual steering wheels to offer an even smoother and more stable ride. The J30-40XN unit is a four wheel lift truck that has manoeuvrability very similar to a three wheel forklift. The four wheel design on this specific model offers a Zero Turning Radius axle that is normally more comfortable if longer distances need to be covered. There are a lot of optional features and many standard features provided on all Hyster forklifts. The optional operator selectable performance mode would allow the driver to set up performance levels from job to job. Further, it could allow a supervisor or manager to set the maximum level of performance when safety could be a concern, like for example if a new driver is learning how to utilize the forklift, helping the operator to learn in a more controlled way. Enclosed operator cabs could be a great option in certain environments to help protect employees from harsh conditions. To keep the workers safe, the enclosed operator cabs provide tempered glass, sound proofing, and an emergency exit. Panoramic and dual rear view mirrors are available to enhance driver visibility, specially of the part behind the forklift and the tail swing area. Impact monitors could be installed that disable the model and require a manager or supervisor to re-enable the forklift. This could help to make certain that employees are safely operating machinery. To prevent forklifts from rolling when the operator intends to stop, an auto park brake is an optional feature which could be included. The park brake applied itself automatically when the unit comes to a complete stop. Certain ratings might be needed for various applications. The approved construction standards and particularly the UL GS, LPS, DS underwriter laboratory rating labels will tell the operator whether the lift truck is equipped with added resistance to spark creation. If there is an issue, there is a mechanical main battery disconnect. An EE UL rating means that the lift truck can be used in work areas where arcs or sparks from electrical machinery could ignite airborne deposits.
Daewoo: Used Daewoo Diesel Forklifts Downey - In the material handling industry, the forklift has become a key piece of machinery. This machinery is also known as a forklift or a powered industrial truck and could transport heavy cargo and materials. These trucks transformed the warehousing and the manufacturing businesses. Now they are utilized for a wide variety of applications and are considered to be essential for material handling. A forklift is a machine that is driven by an operator who uses the truck to move loads around a warehouse or worksite. Companies that own their own lift trucks must maintain the machinery to ensure they have a long lifespan. Lift truck components, similar to any equipment parts, are susceptible to wear and tear and will eventually become worn. In order to make sure the lift truck operates safely and efficiently, you would have to occasionally replace worn or damaged parts. Every lift truck part is made for a specific purpose. Below is a list of some lift truck attachments and their tasks: Forklift Fork Positioner: The forklift fork positioner is a hydraulic attachment that helps to position the forks. It could move the forks either simultaneously or separately. Without the forklift fork positioner, the operator of the lift truck must manually adjust forklift forks for different cargo sizes. Side Shifter: The hydraulic side shift attachment allows the operator to laterally shift the backrest and the forklift forks. This specific type of attachment makes it really easier to position the cargo without having to change the truck's position. Pole Attachments: These long metal poles are intended to lift carpet rolls. The poles work better for this purpose than forklift forks. Telescopic Forklift Forks: Telescoping forks are hydraulic attachments which allow the operator to both unload and load from one side. The telescoping forks can handle two pallets of various sizes at the same time. This specific kind of attachment is great for handling pallets in 'double deep racking'.
TCM: Used TCM Propane Forklifts Downey - Forklift Tank Safety Amongst the most common types of lift trucks available on the market nowadays is a propane-powered lift truck. The propane used to fuel these machines has several properties that should be taken into consideration when working with the fuel tank. Like for instance, it is very vital that all Personal Protective Equipment or PPE is worn each and every time a driver is on the machine and in lots of areas, on the jobsite. PPE Because propane gas is extremely frigid, any contact to your skin, no matter how minor, can lead to serious burns. Hence, it is a requirement that whenever you are exchanging the propane tank or completing a re-fueling process safety goggles or a full face shield and thick gloves need to be worn for protection. A lot of workplaces require steel-toe boots to be worn as well when carrying heavy items is part of your job. Every workplace has various regulations set in place that pertain to the particular needs of the company. Your supervisor will inform you of what kinds of PPE things must be worn prior to your shift starts. No Smoking In the refueling area, there can be no open fire or any kind of smoking going on because of the high flammability factor. Propane gas is highly flammable and it is imperative that it is never exposed to any kind of ignition source or an extremely dangerous exploding situation would unfold. Inspect the Valve Before connecting the fuel line during a tank exchange, make sure that the valve on the new tank is turned off. If you accidentally insert the fuel line into a valve that is open, you would release the propane gas. Neglecting this factor could potentially create a really disastrous situation. Fire Extinguisher A fire extinguisher must be made available, when the tank is being changed out during the refueling process. Most businesses require that a fire extinguisher be mounted on each forklift. This is an important safety regulation that should be made a priority within the workplace. Secure the Tank Most propane tanks use a restraining device like a strap to keep them stable. Be sure that this security feature is correctly functioning as it is being utilized for the important task to stop the tank from falling or shifting. A faulty restraining condition can cause the tank coming loose and falling or rolling around dangerous.
